6V6 SE2

Audio Data 6V6 6sj7 Single

#1 Please forgive me if this subject has been discussed before (or kindly direct me to those threads). I'm looking for information on how to build a single ended, low watt (10-12 watts), studio type amp using a single 6L6, 1-12Ay7 (or a 12AX7) preamp tube, and a 5Y3GT rectifier tube.

I want to try a single 6L6 in my parallel 6V6 Telecaster

This Single-Ended (SE) 6V6 and 6V6GT Tube Amplifier Schematic is from the book Build your own Audio Valve Amplifier by Rainer zur Linde. Either 6V6 or 6V6GT pentode tubes can be used in the output position. The two triodes in the ECC83 (12AX7) are connected in parallel to obtain a low internal resistance.

Single Ended Tube Amplifier Schematic

a class A single ended amp needs a well filtered supply, but not necessarily a low impedance supply. AB stuff really needs low impedance for optimal performance, but it doesn't necessarily have to be wonderfully filtered at the output stage. I have watched what a lousy power supply looks like when trying to run full output power at 30hz.

6l6 Tube Amp Schematics

There has to be a better way. So I decided that I should perform some investigations of the 6V6 in SE-UL operation and see what I could find out. Now in fairness, there is "some" information concerning the 6V6 in UL mode available on the internet.

Parallel 6V6 S.E. amp from 1948 rebuild. Telecaster Guitar Forum

Single ended 2 x 6V6 in parallel schematic ideas? 06-26-2008, 06:24 AM Hi y'all I would like to try building a SE 2 x 6V6GT - cathode biased with a 'verb. It would have a parallel triode Voltage Amplifer stage and separate driver (apart from the reverb) similar to the attached schematic (but with 2 x 6V6GT in parallel)

Single Ended 6V6 HiFi Tube amp Pinterest

This amplifier uses the high gain 12AX7/ECC83 double triode vacuum tube for the preamp stage, and the 6L6GC beam power tube for the output stage in a single-ended Class-A design. Class-A amps are voltage amplifiers. In a Class-A amplifier the output voltage's wave shape is the same with the shape of the signal voltage applied to the grid.

6SL7 driver / PushPull (PP) 6V6 / 6V6GT Tube Amplifier Schematic

12AX7 6V6 Fig 2. Schematic for the amplifier, omitting power supply II. PRE ANALYSIS / DESIGN A. The Input Network The input to the amplifier uses a resistive gamma network. Fig 3. Gamma Network on Input

Push Pull Schematic 6v6 Tube My XXX Hot Girl

Two 6V6 tubes per channel is 1 amp rating and four tubes per channel is 2 amp rating on the 150 volt winding. The 150 volts is rather high with 220uF I would use on the voltage doubler capacitors vs the 22uF shown that does require 150 volts. I would order 120 volts with 220uF voltage doubler capacitors. And, I recommend the 220uF capacitors.

Single Ended 6L6 HiFi (pentode preamp) Tube amp Pinterest

It was designed for an EL95 single ended three Watt circuit. The 16 Ω tap was used for the 8 Ω load to give an effective primary impedance of 5 kΩ. The 6V6 screen grid was taken to the 160 Volt rail used for the 6AT6. The circuit worked well but the power was down at around 1.5 Watts.

6v6 Single Ended Schematic

With the 6V6 you could also look for schematics designed for the EL48. With all due respect it doesn't make any sense to use a high mu tube like the 12AT7 or 12AX7 when you only need a voltage gain of about 25. There are many better sounding tubes to use.

Fender Tweed Champ схема простого однотактного лампового УНЧ на 6V6

Class A Stereo Tube Integrated Amplifier 40-20 Khz TRUE hi-fi Output Transformers (Made in USA) 8 Ohms Speakers Output Only (Tubes doesn't sound good at lower ohms anyway) 4W + 4W Pure Class A Single Set of RCA Input / Purest Signal Path Auto-bias / Maintenance Free Circuit - Just change the tubes in a few years!

FINALE F6V6 Parallel Single Ended Class A Power Amp Photo 2156999

Are you dead set on using the 6V6 as your output valve? You're probably aware it's not actually a triode (SET stands for 'single ended triode) but it can be hooked up in triode mode.

Push Pull Tube Amplifier Schematic

So I ended up with the following schematic for the amplifier. This deceptively simple design has a couple of things going for it. First it uses a 4S Universal preamp circuit as a driver, with the volume control moved to the front. This means that the 12AU7 driver tube can be substituted for a different sound and gain level with any of the.

6v6 Single Ended Amplifier Schematic My XXX Hot Girl

The Electrical Design As I said in the introduction, I decided that I wanted to go with a single ended 6V6 design run in ultra linear mode. To do this I simply took the design point for a single ended class A stage directly off the 6V6 data sheet. This called for a -12.5v bias, a 250v plate and screen voltage, and a 5kΩ plate load.

FINALE F6V6 Parallel Single Ended Class A Power Amp Photo 2156997

Power Supply Schematic The schematic uses a 350 ohm power resistor to limit the B+ such that old style 6V6 tubes can be used. This resistor may be safely omitted if only 6V6GT type tubes are used. Full information on this amplifier build can be found on the 6V6 Lacewood Amp project page.

6v6 Push Pull Amplifier Schematic Diagram Wiring Diagram

Back to 6V6 main page. 6V6 Single-Ended 2. Schematic by Charles W. Harrison Jr. (August 1957). Power 4.2W. Its was used as a treble amp. Amplifier. Power Supply.